Prepare for exam less than 30 hours

It is known to us that time is money, and all people hope that they can spend less time on the pass. We are happy to tell you that The SAP Certified Application Associate - Production - Planning & Manufacturing with SAP ERP 6.0 EHP4 exam questions from our company will help you save time. With meticulous care design, our study materials will help all customers pass their exam in a shortest time. If you buy the C_TSCM42_64 study materials from our company, you just need to spend less than 30 hours on preparing for your exam, and then you can start to take the exam. We believe that you will pass your exam and get the related certification with C_TSCM42_64 study materials.

Our SAP Certified Application Associate - Production - Planning & Manufacturing with SAP ERP 6.0 EHP4 exam questions are designed by a reliable and reputable company and our company has rich experience in doing research about the study materials. We can make sure that all employees in our company have wide experience and advanced technologies in designing the C_TSCM42_64 study materials. So a growing number of the people have used our study materials in the past years, and it has been a generally acknowledged fact that the quality of the C_TSCM42_64 test guide from our company is best in the study materials market. Now we would like to share the advantages of our C_TSCM42_64 study materials to you, we hope you can spend several minutes on reading our introduction; you will benefit a lot from it.

DOWNLOAD DEMO

Acquire more skills

Just like the saying goes, it is good to learn at another man's cost. In the process of learning, it is more important for all people to have a good command of the method from other people. The SAP Certified Application Associate - Production - Planning & Manufacturing with SAP ERP 6.0 EHP4 exam questions from our company will help you find the good study method from other people. Using the C_TSCM42_64 test guide from our company, you can not only pass your exam, but also you will have the chance to learn about the different and suitable study skills. We believe these skills will be very useful for you near life.

Have a 99% pass rate

As the old saying goes, practice is the only standard to testify truth. In other word, it has been a matter of common sense that pass rate of the C_TSCM42_64 test guide is the most important standard to testify whether it is useful and effective for people to achieve their goal. We believe that you must have paid more attention to the pass rate of the SAP Certified Application Associate - Production - Planning & Manufacturing with SAP ERP 6.0 EHP4 exam questions. If you focus on the study materials from our company, you will find that the pass rate of our products is higher than other study materials in the market, yes, we have a 99% pass rate, which means if you take our the C_TSCM42_64 study materials into consideration, it is very possible for you to pass your exam and get the related certification.

SAP Certified Application Associate - Production - Planning & Manufacturing with SAP ERP 6.0 EHP4 Sample Questions:

1. In your company planning strategies are used in the SAP-ECC demand management that are based on consumption. Which of the following statements about consumption is true?
(Choose two.)

A) A consumption situation is dynamic and is always restructured with the planning run.
B) The consumption parameters (consumption mode and consumption interval) can be set in the material master or in the MRP group.
C) Consumption always takes place on the material level between the planned independent requirements and the planned orders.
D) Consumption can also take place between order reservations and planned independent requirements, depending on the strategy.

2. A customer wishes to only produce a finished product when customer orders for it are present. Final assembly should then be carried out at short notice in make-to-order production. Up until this point, the important assemblies needed in final assembly should already be available in stock. Provision of these assemblies should therefore be triggered by planning.
Which options could you offer the customer as useful alternatives in SAP ECC?
(Choose two.)

A) The finished product uses strategy 50 (planning without final assembly) and all the assemblies in the bill of material for the finished product have no strategy.
B) The finished product uses strategy 30 (production by lots) and all the important assemblies in the bill of material for the finished product should have strategy 70 (planning at the assembly level).
C) The finished product uses strategy 40 (planning with final assembly) and all the important assemblies in the bill of material for the finished product should have strategy 70 (planning at the assembly level).
D) The finished product uses strategy 20 (make-to-order production) and all the important assemblies in the bill of material for the finished product should have strategy 70 (planning at the assembly level).

3. Which statement regarding lot size procedures is correct?

A) If a long-term lot size is in use, procurement is conducted with a long-term perspective.
B) If a make-to-order production strategy is in use, a lot for lot (exact) lot size is always determined for the corresponding procurement element.
C) The procurement quantity of a lot size procedure can be specified using a safety time period profile.
D) The lot size quantity can be influenced using a minimum quantity and the rounding profile.

4. A finished material is to be planned in a controlled manner in the SAP ECC system in the context of requirements planning. The planned orders are scheduled using what is known as basic date scheduling (not lead-time scheduling). Which of the following statements is true for the resulting dependent requirements?

A) In multi-level backward scheduling, dependent requirements are triggered at the start date for the higher-level assembly planned order.
B) If individual material components are explicitly assigned to operations during BOM and routing maintenance, the requirement dates of the dependent requirements for these components are scheduled at each of the operation start dates.
C) When a customer order is created for the finished product, the dependent requirements are automatically triggered for the components in the bill of material without a planning run.
D) In multi-level backward scheduling, dependent requirements are triggered at the start date for the higher-level assembly.

5. Which options can you offer a user of the SAP ECC system for managing costs (costing and settlement) with regards to production orders? (Choose two.)

A) Series-based costing
B) Work center-based costing
C) Product cost collecting
D) Order-based costing

Solutions: