[Oct 03, 2021] 350-401 PDF Dumps is essential on your 350-401 Exam Questions Certain Success!
350-401 PDF Questions - Perfect Prospect To Go With 350-401 Practice Exam
NEW QUESTION 137
Refer to the exhibit.
Which command must be applied to Routed to bring the GRE tunnel to an up/up state?
- A. Router1(config-if)#tunnel mode gre multipoint
- B. Router1(config-if)#tunnel source GigabitEthernet0/1
- C. Router1(config)#interface tunnel0
- D. Router1(config-if)#tunnel source Loopback0
Answer: D
Explanation:
In order to make a Point-to-Point GRE Tunnel interface in up/up state, two requirements must be met: + A valid tunnel source (which is in up/up state and has an IP address configured on it) and tunnel destination must be configured + A valid tunnel destination is one which is routable. However, it does not have to be reachable.
NEW QUESTION 138
Drag and drop the solutions that comprise Cisco Cyber Threat Defense from the left onto the objectives they accomplish on the right.
Answer:
Explanation:
NEW QUESTION 139
Refer the exhibit.
Which router is the designated router on the segment 192.168.0.0/24?
- A. Router NewYork because it has a higher router ID
- B. This segment has no designated router because it is a p2p network type.
- C. Router Chicago because it has a lower router ID
- D. This segment has no designated router because it is a nonbroadcast network type.
Answer: D
NEW QUESTION 140
Refer to the exhibit.
Assuming the WLC's interfaces are not in the same subnet as the RADIUS server, which interface would the WLC use as the source for all RADIUS-related traffic?
- A. the interface specified on the WLAN configuration
- B. any interface configured on the WLC
- C. the controller management interface
- D. the controller virtual interface
Answer: A
NEW QUESTION 141
Refer to the exhibit.
Which type of antenna does the radiation pattern represent?
- A. Yagi
- B. directional patch
- C. omnidirectional
- D. multidirectional
Answer: A
NEW QUESTION 142
Refer to the exhibit.
A network engineer is configuring OSPF between router R1 and router R2. The engineer must ensure that a DR/BDR election does not occur on the Gigabit Ethernet interfaces in area 0. Which configuration set accomplishes this goal?
A)
B)
C)
D)
- A. Option A
- B. Option D
- C. Option B
- D. Option C
Answer: A
Explanation:
Explanation
Broadcast and Non-Broadcast networks elect DR/BDR while Point-topoint/
multipoint do not elect DR/BDR. Therefore we have to set the two Gi0/0
interfaces to point-to-point or point-to-multipoint network to ensure that a DR/BDR election does not occur.
NEW QUESTION 143
Drag and drop the characteristics from the left onto the infrastructure types on the right.
Answer:
Explanation:
Explanation
NEW QUESTION 144 
Refer to the exhibit. An engineer is using XML in an application to send information to a RESTCONF-enabled device. After sending the request, the engineer gets this response message and a HTTP response code of 400. What do these responses tell the engineer?
- A. The Content-Type header sent was application/xml.
- B. POST was used instead of PUT to update
- C. The Accept header sent was application/xml
- D. JSON body was used
Answer: C
Explanation:
Explanation
Accept and Content-type are both headers sent from a client (a browser) to a service. Accept header is a way for a client to specify the media type of the response content it is expecting and Content-type is a way to specify the media type of request being sent from the client to the server.
The response was sent in XML so we can say the Accept header sent was application/xml.
NEW QUESTION 145
Which method creates an EEM applet policy that is registered with EEM and runs on demand or manually?
- A. event manager applet ondemand
event register
action 1.0 syslog priority critical msg 'This is a message from ondemand' - B. event manager applet ondemand
event none
action 1.0 syslog priority critical msg 'This is a message from ondemand' - C. event manager applet ondemand
action 1.0 syslog priority critical msg 'This is a message from ondemand' - D. event manager applet ondemand
event manual
action 1.0 syslog priority critical msg 'This is a message from ondemand'
Answer: B
Explanation:
Explanation
An EEM policy is an entity that defines an event and the actions to be taken when that event occurs. There are two types of EEM policies: an applet or a script. An applet is a simple form of policy that is defined within the CLI configuration. answer 'event manager applet ondemand event register action 1.0 syslog priority critical msg 'This is a message from ondemand'
<="" p="" style="box-sizing: border-box;">
There are two ways to manually run an EEM policy. EEM usually schedules and runs policies on the basis of an event specification that is contained within the policy itself. The event none command allows EEM to identify an EEM policy that can be manually triggered. To run the policy, use either the action policy command in applet configuration mode or the event manager run command in privileged EXEC mode.
Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/eem/configuration/xe-3s/eem-xe-3s-book/eem-policy-cli.html
NEW QUESTION 146
The login method is configured on the VTY lines of a router with these parameters The first method for authentication it TACACS If TACACS is unavailable login is allowed without any provided credentials Which configuration accomplishes this task?
- A. Option D
- B. Option B
- C. Option A
- D. Option C
Answer: B
NEW QUESTION 147
Which function is handled by vManage in the Cisco SD-WAN fabric?
- A. Establishes BFD sessions to test liveliness of links and nodes
- B. Establishes IPsec tunnels with nodes.
- C. Distributes policies that govern data forwarding
- D. Performs remote software upgrades for WAN Edge. vSmart and vBond
Answer: A
NEW QUESTION 148
Drag and drop the LISP components from the left onto the function they perform on the right. Not all options are used.
Answer:
Explanation:
Explanation:
+ accepts LISP encapsulated map requests: LISP map resolver
+ learns of EID prefix mapping entries from an ETR: LISP map server
+ receives traffic from LISP sites and sends it to non-LISP sites: LISP proxy ETR
+ receives packets from site-facing interfaces: LISP ITR
Explanation
ITR is the function that maps the destination EID to a destination RLOC and then encapsulates the original packet with an additional header that has the source IP address of the ITR RLOC and the destination IP address of the RLOC of an Egress Tunnel Router (ETR).
After the encapsulation, the original packet become a LISP packet.
ETR is the function that receives LISP encapsulated packets, decapsulates them and forwards to its local EIDs. This function also requires EID-to-RLOC mappings so we need to point out an "map-server" IP address and the key (password) for authentication.
A LISP proxy ETR (PETR) implements ETR functions on behalf of non-LISP sites. A PETR is typically used when a LISP site needs to send traffic to non-LISP sites but the LISP site is connected through a service provider that does not accept no routable EIDs as packet sources. PETRs act just like ETRs but for EIDs that send traffic to destinations at non-LISP sites.
Map Server (MS) processes the registration of authentication keys and EID-to-RLOC mappings. ETRs sends periodic Map-Register messages to all its configured Map Servers.
Map Resolver (MR): a LISP component which accepts LISP Encapsulated Map Requests, typically from an ITR, quickly determines whether or not the destination IP address is part of the EID namespace
NEW QUESTION 149
Running the script causes the output in the exhibit. Which change to the first line of the script resolves the error?
- A. from ncclient import
- B. from ncclient import*
- C. import ncclient manager
- D. import manager
Answer: B
NEW QUESTION 150
Drag and drop the virtual components from the left onto their deceptions on the right.
Answer:
Explanation:
NEW QUESTION 151
What are two reasons a company would choose a cloud deployment over an on-prem deployment? (Choose Two)
- A. In a cloud environment, the company is in full control of access to their data. On-prem risks access to data due to service provider outages
- B. Cloud costs adjust up or down depending on the amount of resources consumed. On- Prem costs for hardware, power, and space are ongoing regardless of usage
- C. In a cloud environment, the company controls technical issues. On-prem environments rely on the service provider to resolve technical issue.
- D. Cloud resources scale automatically to an increase in demand. On-prem requires additional capital expenditure.
- E. Cloud deployments require long implementation times due to capital expenditure processes. On-Prem deployments can be accomplished quickly using operational expenditure processes.
Answer: B,D
Explanation:
Explanation
NEW QUESTION 152 
Refer to the exhibit. Which code results in the working python script displaying a list of network devices from the Cisco DNA center?
- A. Option A
- B. Option D
- C. Option B
- D. Option C
Answer: A
NEW QUESTION 153
Which statement about multicast RPs is true?
- A. RPs are required only when using protocol independent multicast dense mode.
- B. By default, the RP is needed only to start new sessions with sources and receivers.
- C. By default, the RP is needed periodically to maintain sessions with sources and receivers
- D. RPs are required for protocol independent multicast sparse mode and dense mode.
Answer: B
NEW QUESTION 154
......
350-401 Exam with Accurate Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) PDF Questions: https://www.exams4sures.com/Cisco/350-401-practice-exam-dumps.html
True Cisco Exam Extraordinary Practice For the 350-401 Exam: https://drive.google.com/open?id=1Dt4crYkisXWlJxKgHedpJCx9Md5GHJxU