NACE-CIP2-001 Revolutionary Guide To Exam NACE Dumps
NACE-CIP2-001 Free Study Guide! with New Update 100 Exam Questions
Achieving the NACE-CIP2-001 certification demonstrates a high level of expertise in the coatings industry and can lead to greater opportunities for career advancement. Certified coating inspectors are often sought after by companies in a variety of industries, including oil and gas, construction, and manufacturing. They may also be eligible for higher salaries and increased job security.
NEW QUESTION # 38
The primary purpose of Fireproofing coatings are to provide:
- A. Explosion resistance
- B. Temporary protection for the structure
- C. Preferential fuel for the fire
- D. fire extinguishing characteristics
Answer: B
NEW QUESTION # 39
When performing testing in accordance with ASTM D 2583 the inspector may observe:
- A. Glue failure
- B. Adhesion failure
- C. Cold flow or creep
- D. Cohesion failure
Answer: C
NEW QUESTION # 40
In which type of concrete are laitance commonly encountered?
- A. Poured (wet cast)
- B. Concrete block (poured with a form)
- C. Glass fiber cement
- D. Gunite
Answer: A
NEW QUESTION # 41
When observing fabrication defects the NACE Inspector should:
- A. Write an NCR and call the fabricator
- B. Require they be corrected prior to coating
- C. Consult the specification to determine how they should be treated
- D. Stop the job immediately
Answer: C
NEW QUESTION # 42
Dehumidification is defined as the removal of moisture vapor from the air to
- A. lower its temperature
- B. provide worker comfort.
- C. lower its dew point,
- D. raise its relative humidity.
Answer: C
NEW QUESTION # 43
You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.
Your FIRST preferred course of action is to:
- A. Refuse to take readings until an is in place
- B. Use a generally accepted industry standard and to take readings
- C. Develop your own methodology and proceed take the readings
- D. Call your supervisor
Answer: B
NEW QUESTION # 44
A failure caused by applying a coating too thinly is known as
- A. pinholes.
- B. chalking.
- C. failure to cure.
- D. cracking.
Answer: A
NEW QUESTION # 45
Which standards are generally established by private-sector bodies and are available for use by any person or Organization, private or government?
- A. De facto
- B. Voluntary
- C. Mandatory
- D. Consensus
Answer: B
NEW QUESTION # 46
You are the NACE Inspector on a project where a stationary floating structure is being coated and you notice a self-smoothing anti-fouling coating has been specified.
This is not a good choice because:
- A. The floating structure is stationary
- B. It will result in a very slippery surface
- C. It doesn't contain biocide
- D. It contains biocide
Answer: D
NEW QUESTION # 47
Which surface preparation method uses a dilute acid solution to remove laitance and I roughen the concrete surface?
- A. Stoning
- B. Acid etching
- C. Sacking
- D. High-pressure water washing
Answer: B
NEW QUESTION # 48
Inspection and Test Plans are provided to:
- A. To supersede the requirements of the product data sheets
- B. So the contractor has a single document to reference
- C. So the Inspector doesn't have to read the entire specification
- D. Outline the inspection steps, sequencing and pass/fail criteria
Answer: D
NEW QUESTION # 49
Surface preparation methods for Non-ferrous metals are:
- A. Not required
- B. Specific for each type of Non-ferrous metal
- C. The same as for Ferrous metals
- D. The same for all Non-FetT0us metals
Answer: B
NEW QUESTION # 50
Differences in technique for abrasive blasting concrete versus steel require the operator to:
- A. Lower the blast pressure
- B. a), b) and c)
- C. Increase the standoff distance
- D. Move the nozzle quicker
Answer: B
NEW QUESTION # 51
Corrosion is the reverse process of
- A. flaking.
- B. hot dipping.
- C. galvanic deterioration.
- D. steel manufacturing.
Answer: D
NEW QUESTION # 52
When ASIN D 3363 is specified the Inspector must:
- A. Use the correct solvent
- B. Record the two end points identified in the standard
- C. Record the percentage of failure
- D. Record the highest value attained
Answer: B
NEW QUESTION # 53
The number of air turns in an enclosure can be affected by all of these EXCEPT
- A. time of the year (winter/summer).
- B. type of dehumidification equipment (refrigerant or desiccant).
- C. coating type.
- D. manufacturer of the equipment.
Answer: C
NEW QUESTION # 54
External coatings applied to buried pipelines are generally tested for:
- A. Solvent resistance
- B. Cathodic disbondment
- C. Chalking resistance
- D. Gloss level
Answer: B
NEW QUESTION # 55
Galvanizing performs best in which of the following exposures:
- A. pH above 12
- B. pH between 5-10
- C. pH below 4
- D. pH of 13
Answer: B
NEW QUESTION # 56
When performing a hardness test on a coating which has elastic properties the inspector is likely to likely to observe:
- A. A very high reading
- B. A very low reading
- C. No difference from any other coating
- D. Cold flow or creep
Answer: D
NEW QUESTION # 57
From a corrosion perspective, the main difference between Ferrous and Non-Ferrous Metals is:
- A. Iron content
- B. Safety
- C. Cost
- D. Appearance
Answer: A
NEW QUESTION # 58
The standards defining surface cleanliness achieved by centrifugal blast cleaning are:
- A. Different than air blast cleaning
- B. Slightly different to air blast cleaning
- C. Comparable to air blast cleaning
- D. The same as air blast cleaning
Answer: D
NEW QUESTION # 59
The Inspectors' goal at the Pre-Job Conference is to:
- A. Manage the meeting so it doesn't go off topic
- B. Take accurate meeting minutes for distribution
- C. Obtain a clear understanding of the Specification
- D. Discuss contractual requirements
Answer: C
NEW QUESTION # 60
Coating surveys may include which steps?
Select All That Apply:
- A. Schedule the remedial work
- B. Summarize the collected data
- C. Evaluate the coatings performance
- D. Develop a survey plan
Answer: A,B,C,D
NEW QUESTION # 61
A single component water borne acrylic coating cures by:
- A. Oxidation
- B. Solvent Evaporation
- C. Coalescence
- D. Co-Reaction
Answer: C
NEW QUESTION # 62
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
- A. 2-Layer Polyethylene (PE)
- B. Coal Tar Enamel
- C. Fusion Bonded Epoxy
- D. 3-Layer Polyethylene (PE)
Answer: D
NEW QUESTION # 63
......
NACE-CIP2-001 certification is important for coating inspectors because it demonstrates their knowledge and skills in the field of coating inspection. Coating Inspector Level 2 certification is widely recognized by employers and can help coating inspectors advance their careers. In addition, the certification is a requirement for many coating inspection jobs, particularly in the oil and gas industry.
NACE-CIP2-001 certification exam is divided into two parts: a written exam and a practical exam. The written exam consists of 120 multiple-choice questions, and candidates have four hours to complete it. The practical exam consists of hands-on inspections of coatings and is designed to test a candidate's ability to apply their knowledge and skills in a real-world setting. Candidates must pass both parts of the exam to earn their NACE-CIP2-001 certification.
Get up-to-date Real Exam Questions for NACE-CIP2-001: https://www.exams4sures.com/NACE/NACE-CIP2-001-practice-exam-dumps.html
Pass NACE-CIP2-001 Exam Latest Practice Questions: https://drive.google.com/open?id=1VpWqIiohBdI5q4NgaYXr8dLeNzORFc0d